Can you thin out Thompson Water Seal?

Photo of author
Written By Thurman Schinner

Can you thin out Thompson Water Seal? The old-timer came up with a similar formula in 3 parts linseed oil, 2 parts Thompson?s Water Seal cut with 1 part paint thinner. The paint thinner acts as a penetrating agent, making the mixture thin enough so that the active ingredients penetrate the wood.
Can you dilute Thompson?s water sealer??Use at full strength. Do not dilute. COVERAGE Thompson?s Water Seal will cover approximately 4 m? per litre. Coverage will vary depending on the texture and porosity of the surface to being treated.$MMT = window.$MMT || {}; $MMT.cmd = $MMT.cmd || [];$MMT.cmd.push(function(){ $MMT.video.slots.push([“6451f103-9add-4354-8c07-120e2f85be69”]); })
Can you use a pump sprayer to apply Thompson?s water Seal??To apply Thompson?s water seal with a sprayer, you can use a garden sprayer with a hose or a pump sprayer. However, the manufacturer of Thompson?s water seal recommends that their product be used with a plastic sprayer and a brass wand.
Can you use too much Thompson Water Seal??If over-application occurs and there is puddling of the product, redistribute product within 15 minutes to a dry area or wipe off. Q: Will the formula of Thompson?s? WaterSeal? Sport Seal? or Fabric Seal change the feel of the treated surface? No. These products will not change the surface?s feel or leave it sticky.
Can you thin out Thompson Water Seal? ? Related Questions
Can you recoat Thompson Water Seal?
The waterproofing nature of Thompson?s precludes using a water based product as a stain or paint. Recoat over the Thompson?s Clear product the following season with a 100% oil and petrochemical based product, clear or stained, such as TWP, Armstrong-Clark, Penofin (Penetrating Oil Finish).
Can I apply 2 coats of Thompson?s Water Seal?
Apply 2 coats using brush,roller or sprayer. note: Use at full strength.do not dilute. The second coat should be applied when the first coat has soaked in the surface. For best results do not leave the first coat to dry for more than 1 hour before applying the second coat.
Is Thompson?s Water Seal any good?
? Thompson?s? WaterSeal? Clear did not alter or change the appearance of the wood. After full drying, we tested the ability to repel water. Water did bead on top of the finish and did not absorb into the wood. ? As far as we can tell, Thompson?s? WaterSeal? does not prevent UV graying at all.
How many coats of Thompson Water Seal do I need?
One coat is enough, but if more color is desired, a second coat can be applied within two hours before the first coat has dried. With Thompson?s? WaterSeal? Waterproofing Stains, you can clean your tools with soap and water.
How long does Thompson water Seal still tacky?
Though your water sealing won?t be weakened (or at least, it?s highly unlikely that it?s going to wash away), it will have a longer dry time than the standard 24 hours. After two to three days, you probably won?t have any stickiness left on your wood.
How long does Thompson?s water Seal last?
If applied correctly, Water Seal will last up to 4 years. This is dependent on conditions such as orientation of the wall and local climate.
When can I walk on Thompson?s water Seal?
Now that you?ve applied Thompson?s Water Seal following the instructions above, to your entire surface, you can walk away and let it dry for 24 hours. That?s all the time you need to let Thompson?s Water Seal work to protect your outdoor surfaces from water damage.
What is the best way to apply Thompson?s Water Seal?
The fastest way to apply is with a pump-up sprayer (using a coarse setting), but you can also apply with a brush or a roller. You should apply liberally. In the case of areas with heavy discoloration or dirt, apply a second coat, brush lightly with a broom and hose off.
How do I dispose of Thompson Water Seal?
CONTAINER DISPOSAL: Triple rinse (or equivalent). Then offer for recycling or reconditioning, or dispose of in a sanitary landfill, or by incineration if allowed by state and local authorities.
What can I put over Thompsons Water Seal?
You can only paint over Thompson?s Water Seal if you wait 45 days and use a primer. This only works if you paint over concrete, but paint doesn?t always stick to the Thompson?s seal well. Your paint may not look as intended because Thompson?s Water Seal has hydrophobic tendencies.
Is it better to seal or stain a deck?
Sealing a deck is best for cedar, teak, mahogany, or other quality woods as it enhances the wood grain and natural color. Staining a deck protects the wood from mold, mildew, moisture, and rot, and UV rays and sun damage.
Can you use Thompson water Seal on pressure treated wood?
However, most of the water-repellent sealers sold at home centers, paint stores and lumber yards are suitable for pressure-treated wood as well as other outdoor woods such as cedar and redwood. The directions for some, such as Thompson?s Water Seal, specify pressure-treated wood as a suitable use.
Is Thompson Water Seal oil or water based?
Thompson?s? WaterSeal? Penetrating Timber Oil is an oil-based product that provides protection by penetrating into wood pores and sealing out water infiltration. Thompson?s? WaterSeal? Waterproofing Stains are water-based products that have film-forming properties to protect the wood by repelling water.
What is the longest lasting deck sealer?
Q. What is the longest-lasting deck sealer? An oil-based deck sealer, such as Rust-Oleum Ultimate Spar Urethane, will protect a deck for up to 5 years.
What if it rains after sealing deck?
Rain will damage the finish of any wet sealer with linseed oil or mineral oil in it. Because it forms a coating, it takes several hours to dry, and during that time, the sealer is vulnerable. After the rain has passed and the deck has dried, take a closer look.
How long does Thompson Water Seal need to dry before rain?
For deck stain, the deck surface and air temperature should be between 50 and 95 Fahrenheit for application and drying. The forecast should indicate no rain for at least 24 hours after application. The deck surface should be allowed to dry for at least 48 hours before application.
Why is my concrete sealer sticky?
Is there something I can do to get the stickiness off? A. Too much stain residue remaining on the surface when sealing is the most common cause of sealer failure on stained concrete floors. Stripping the sealer where it is tacky, neutralizing and cleaning the floor, then re-sealing should correct the problem.
How often do you need to seal your deck?
For most decks, sealing once each year is a good rule of thumb. Depending on the condition of your deck this can be adjusted, but keep in mind that you should never go beyond three years maximum before re-sealing and staining.
Is Thompson?s Water Seal toxic?
Environmentally safe, will not harm plants, pets, fish, livestock, humans. Contains zero volatile organic compounds (VOC). No toxic fumes. Seals and protects with single application on most surfaces.
Should you put a sealer over stain?
Applying a topcoat sealer is not required, but a finish protects the stained wood from scratches and keeps it from fading over time. If applying a polyurethane finish with a brush, apply one to two coats. If using a spray can, hold 8 to 12 inches from the surface and apply two or three light coats.
What happens if you don?t seal stained wood?
A: If you don?t apply some kind of sealer the wood will be dried-out and lifeless. When you rub stain into wood, it brings out the grain pattern and gives the wood a more dramatic look. The final step in staining wood is to wipe off any excess, so the process leaves nothing behind.

See also  What order should I watch the Scorpion King in?